freebsd 7.0 on a dell vostro 1400 /sbin/dmesg output

i purchased a dell vostro 1400 to use as a freebsd development-on-the-go machine only to discover that neither the physical or wireless ethernet is supported.

here’s the /sbin/dmesg output:

Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
 The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RELEASE #0: Sun Feb 24 19:59:52 UTC 2008
    root@logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Duo CPU     T7500  @ 2.20GHz (2193.89-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6fb  Stepping = 11
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  Cores per package: 2
real memory  = 2137444352 (2038 MB)
avail memory = 2082070528 (1985 MB)
ACPI APIC Table: <DELL   M08    >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0: Changing APIC ID to 2
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 19:59:27)
acpi0: <DELL M08    > on motherboard
acpi0: [ITHREAD]
Timecounter "HPET" frequency 14318180 Hz quality 900
acpi0: reservation of 0, 9f000 (3) failed
acpi0: reservation of 100000, 7f56d800 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xeff8-0xefff mem 0xfea00000-0xfeafffff,0xe0000000-0xefffffff irq 16 at device 2.0 on pci0
agp0: <Intel GM965 SVGA controller> on vgapci0
agp0: detected 7676k stolen memory
agp0: aperture size is 256M
vgapci1: <VGA-compatible display> mem 0xfeb00000-0xfebfffff at device 2.1 on pci0
uhci0: <UHCI (generic) USB controller> port 0x6f20-0x6f3f irq 20 at device 26.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0x6f00-0x6f1f irq 21 at device 26.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfed1c400-0xfed1c7ff irq 22 at device 26.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb2: EHCI version 1.0
usb2: companion controllers, 2 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
uhub2: 4 ports with 4 removable, self powered
pci0: <multimedia> at device 27.0 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci11: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 28.1 on pci0
pci12: <ACPI PCI bus> on pcib2
pci12: <network> at device 0.0 (no driver attached)
pcib3: <ACPI PCI-PCI bridge> at device 28.3 on pci0
pci13: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 28.5 on pci0
pci9: <ACPI PCI bus> on pcib4
pci9: <network, ethernet> at device 0.0 (no driver attached)
uhci2: <UHCI (generic) USB controller> port 0x6f80-0x6f9f irq 20 at device 29.0 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb3: <UHCI (generic) USB controller> on uhci2
usb3: USB revision 1.0
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0x6f60-0x6f7f irq 21 at device 29.1 on pci0
uhci3: [GIANT-LOCKED]
uhci3: [ITHREAD]
usb4: <UHCI (generic) USB controller> on uhci3
usb4: USB revision 1.0
uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub4: 2 ports with 2 removable, self powered
uhci4: <UHCI (generic) USB controller> port 0x6f40-0x6f5f irq 22 at device 29.2 on pci0
uhci4: [GIANT-LOCKED]
uhci4: [ITHREAD]
usb5: <UHCI (generic) USB controller> on uhci4
usb5: USB revision 1.0
uhub5: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb5
uhub5: 2 ports with 2 removable, self powered
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfed1c000-0xfed1c3ff irq 20 at device 29.7 on pci0
ehci1: [GIANT-LOCKED]
ehci1: [ITHREAD]
usb6: EHCI version 1.0
usb6: companion controllers, 2 ports each: usb3 usb4 usb5
usb6: <EHCI (generic) USB 2.0 controller> on ehci1
usb6: USB revision 2.0
uhub6: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb6
uhub6: 6 ports with 6 removable, self powered
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci3: <ACPI PCI bus> on pcib5
fwohci0: <1394 Open Host Controller Interface> mem 0xfe4ff800-0xfe4fffff irq 19 at device 1.0 on pci3
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 39:4f:c0:00:10:49:85:c1
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x7d088000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 3a:4f:c0:49:85:c1
fwe0: Ethernet address: 3a:4f:c0:49:85:c1
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 39:4f:c0:00:10:49:85:c1 @ 0xfffe00000000, S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
pci3: <base peripheral> at device 1.1 (no driver attached)
pci3: <base peripheral> at device 1.2 (no driver attached)
pci3: <base peripheral> at device 1.3 (no driver attached)
pci3: <base peripheral> at device 1.4 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ATA controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x6fa0-0x6faf irq 16 at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
atapci1: <Intel AHCI controller> port 0x6eb0-0x6eb7,0x6eb8-0x6ebb,0x6ec0-0x6ec7,0x6ec8-0x6ecb,0x6ee0-0x6eff mem 0xfe9fb800-0xfe9fbfff irq 17 at device 31.2 on pci0
atapci1: [ITHREAD]
atapci1: AHCI Version 01.10 controller with 3 ports detected
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: port not implemented
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci1
ata4: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64,0x62,0x66 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model GlidePoint, device ID 0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcefff,0xcf000-0xcffff pnpid ORM0000 on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
hptrr: no controller detected.
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
acd0: CDRW <HL-DT-STCD-RW/DVD-ROM GCC-T10N/A100> at ata0-master UDMA33
ad4: 114473MB <FUJITSU MHY2120BH 0085000B> at ata2-master SATA150
GEOM_LABEL: Label for provider acd0 is iso9660/VISTA_32_ULTIMATE.
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad4s1a
umass0: <SanDisk U3 Cruzer Micro, class 0/0, rev 2.00/0.10, addr 2> on uhub6
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <SanDisk U3 Cruzer Micro 4.05> Removable Direct Access SCSI-2 device 
da0: 40.000MB/s transfers
da0: 1952MB (3999373 512 byte sectors: 255H 63S/T 248C)
cd0 at umass-sim0 bus 0 target 0 lun 1
cd0: <SanDisk U3 Cruzer Micro 4.05> Removable CD-ROM SCSI-2 device 
cd0: 40.000MB/s transfers
cd0: Attempt to query device size failed: UNIT ATTENTION, Not ready to ready change, medium may have changed

Powered by WordPress | Designed by Elegant Themes